Altigen-comm TRITON T1 Uživatelský manuál stáhnout pdf

TRITON T1 BOARD

QUICK INSTALLATION GUIDE

MINIMUM

SYSTEM REQUIREMENTS:

• IBM/PC AT compatible system with adequate number of full-size ISA and PCI slots

• 233 Mhz Pentium processor (or better)

• 2 - 4 GB Hard Disk Drive Space (depending on voicemail requirements)

• Windows NT Server 4.0 with Service Pack 4 (or higher) installed

• 128 MB RAM

• AltiGen’s Quantum Telephony Board (one or more, Rev. D or higher)

• AltiGen’s Triton T1 Board (one or more)

• AltiWare OE R3.0 (or higher)

• 300W/10A CPU Power (minimum required to power AltiGen boards only)

• CSU (Channel Service Unit)

*** Faulty signals include the following: yellow alarm, bipolar violation or frame error

MVIP BUS

Termination Switch

MVIP Connector

TRITON T1 BOARD

System

Configuration Switch

# of AltiGen Boards # of Slots** CPU HDD

1 Triton T1, 1-3 Quantum 2 PCI, 3 ISA 233 Mhz 2GB

1 Triton T1, 1-6 Quantum 2 PCI, 6 ISA 300 Mhz 2GB

1-4 Triton T1, 1-10 Quantum 5 PCI, 10 ISA 350 Mhz 4GB

# of AltiGen Boards Power Supply** Typical Power Supply

1 Triton T1, 1-3 Quantum +12V: 4.2 Amps +5V: 6Amps 300W/30A@5V/12A@12V

1 Triton T1, 1-6 Quantum +12V: 8.4 Amps +5V: 10.8Amps 400W/40A@5V/16A@12V

1-4 Triton T1, 1-10 Quantum +12V: 14 Amps +5V: 21Amps 400W/40A@5V/16A@12V

GREEN LED RED LED Status

OFF OFF No power

ON OFF Normal operation

OFF ON No signal

ON Flashing Faulty signal with frame synchronization***

OFF Flashing Faulty signal without frame synchronization

Alternating Alternating Frame slips in normal operation

The Triton T1 Board uses the following signaling and framing features:

Signaling: loop start, ground start, E&M immediate start, E&M wink start*

Line Encoding: AMI, B8ZS*

*recommended

** The above system requirements are for AltiGen components only, and do not take into account requirements for other

system components such as motherboard, disk drives, etc.

LED Indicators

1 2 3 4

Shrnutí obsahu

Strany 1 - TRITON T1 BOARD

TRITON T1 BOARDQUICK INSTALLATION GUIDEMINIMUMSYSTEM REQUIREMENTS:• IBM/PC AT compatible system with adequate number of full-size ISA and PCI slots• 2

Strany 2 - CPU 3 2 1 0

STEP 1: MAKE SURE BOARD ID OF QUANTUM BOARD(S) IS SET PROPERLYThe first (outer-most) Quantum board ID should be set as 0, the next boardID as 1, and s

Strany 3

STEP 3: CONNECT THE MVIP CABLE AND TERMINATE THE MVIP BUSSTEP 4: CONNECT CSU (CHANNEL SERVICE UNIT) TO TRITON T1 BOARDUsing Adtran’s CSU (model T1 CSU

Strany 4 - AltiGen Communications, Inc

STEP 6: TURN SYSTEM ON AND INSTALL ALTIWARE OEOR START ALTIWARE OE TO CONFIGURE NEW T1 TRUNKS• End users, please contact your Authorized AltiGen Deale

Komentáře k této Příručce

Žádné komentáře

Altigen-comm TRITON T1 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Hardware Altigen-comm TRITON T1. AltiGen comm TRITON T1 User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce